Rockboard

With the RockBoard® HA 2 in-ear monitor volume controller, the volume of the monitor signal sent from the mixing console can be quickly adjusted to the actual needs of the musician without having to signal a sound engineer to reduce the volume. The lightweight, wired device with belt clip is designed for musicians who do not have to move far on stage. It works as a passive volume control and does not require batteries.

The RockBoard HA 1 in-ear monitoring headphone amplifier is the ideal companion for singers, keyboardists, drummers, guitarists, bassists and other musicians. It establishes the connection between the monitor signal from the mixing console, instrument or amp and your own headphones. Operation is child's play: simply activate the device with the volume control and set the desired volume for the headphone signal. With the stereo/mono source switch, which is easily accessible on the device, the RockBoard HA 1 can be adjusted to the available input signal. The extremely compact and lightweight aluminium housing is fitted with a clip for attaching to a belt or waistband. The HA 1 has a status LED which changes colour depending on the available battery voltage. Two AAA batteries (not included) provide up to 12 hours of power supply and the batteries can be changed in no time at all thanks to the practical battery compartment with clip fastener, which is accessible from the outside. The HA 1 is equipped with a combination socket for use with stereo jack (6.35 mm) and XLR cables for the input signal and a 3.5 mm stereo jack headphone output. On stage, in the rehearsal room or at home, the RockBoard HA 1 in-ear monitoring headphone amplifier always offers full control over the monitoring signal. In small clubs, in-ear monitoring improves the acoustics in the room, and when the band turns up the volume again, the signal is quickly adjusted and you can enjoy the same sound in every part of the room.

The Power MOD ISO DC 1 is a multi power supply unit for effect pedals and offers up to 9 galvanically isolated, elaborately filtered 9 VDC power connections and a 5 V USB connection. The multi power supply is designed to supply up to 9 effect pedals with power simultaneously without generating background noise. Sophisticated filter technology effectively eliminates high-frequency interference. Separate short-circuit protection for each output protects the connected effects pedals from damage in the event of a short circuit. Independently operating LEDs signal the correct status of the connection at each output. In the event of a short circuit, only the affected output is switched off, the rest of the effect pedals remain operational.

The RockBoard ISO Power Block 12 IEC is a multi power supply unit for effects pedals and offers 12 galvanically isolated, highly filtered power connections and a 5V USB connection. The multi power supply was developed to supply up to 12 effect pedals, even with different operating voltages, with power simultaneously and silently. The advanced filter technology effectively prevents high-frequency background noise. The separate short-circuit protection protects the connected effect pedals from damage in the event of a short circuit. Separate LEDs indicate short circuits for each individual connection. If a short circuit occurs, only the affected output is switched off, so that the smooth operation of the remaining connections is still guaranteed.

The revised RockBoard® MODs V2 are simple all-in-one patchbays for the RockBoard Pedalboard Series with a new, revised design and a compact housing. Suitable for all new RockBoards® (except the DUO series) with a MOD slot, they provide a convenient patchbay with various cable connections to cover a wide range of needs. With the RockBoard® MODs you can permanently wire your pedals under the board and organise all connections to and from your effects setup in one convenient module. The RockBoard® MODs provide a central access point from the instrument to the amp as well as a convenient and easy power supply to the board via an IEC and a 2.1 x 5.5 barrel-through power connector. The RockBoard® MOD 1 V2 is a pass-through box designed specifically for guitarists and bassists. You can use the MOD 1 V2 to position several pedals of your setup in the front end and effects loop of the amplifier (4-cable method) or use the four TRS connectors as the central input and output of the board. The XLR through connection can be used as a signal output from the pedalboard to the mixing console or PA.

The RockBoard PedalSafe system is designed to keep effects pedals safe, clean and in pristine condition. The flexible PedalSafe Type J protective cover and universal pedal mounting plate fit medium size Strymon effects pedals. You can see the settings through the crystal-clear pedal cover, but they are optimally protected against unintentional adjustment by the cover. The set includes the protective cover (PedalSafe) and the universal mounting plate. The RockBoard Universal Pedal Mounting Plate was developed to securely mount effects pedals with the PedalSafe system on almost all pedalboards that do not have the innovative RockBoard Slot Grid. The mounting plates can be screwed onto the back of the pedals using the original screws (or the supplied replacement screws) and easily removed without leaving any residue.

The RockBoard ISO Power Block 9 IEC is a multi power supply unit for effects pedals and offers 9 galvanically isolated, highly filtered power connections and a 5V USB connection. The multi power supply was developed to supply up to 9 effect pedals, even with different operating voltages, with power simultaneously and silently. The advanced filter technology effectively prevents high-frequency background noise. The separate short-circuit protection protects the connected effect pedals from damage in the event of a short circuit. Separate LEDs indicate short circuits for each individual connection. If a short circuit occurs, only the affected output is switched off, so that the smooth operation of the remaining connections is still guaranteed.

The RockBoard ISO Power Block 6 IEC is a multi power supply unit for effects pedals and offers 6 galvanically isolated, highly filtered power connections and a 5V USB connection. The multi power supply was developed to supply up to 6 effect pedals, even with different operating voltages, with power simultaneously and silently. The advanced filter technology effectively prevents high-frequency background noise. The separate short-circuit protection protects the connected effect pedals from damage in the event of a short circuit. Separate LEDs indicate short circuits for each individual connection. If a short circuit occurs, only the affected output is switched off, so that the smooth operation of the remaining connections is still guaranteed.

The revised RockBoard® MODs V2 are simple all-in-one patchbays for the RockBoard Pedalboard Series with a new, revised design and a compact housing. Suitable for all new RockBoards® (except the DUO series) with a MOD slot, they provide a convenient patchbay with various cable connections to cover a wide range of needs. With the RockBoard® MODs you can permanently wire your pedals under the board and organise all connections to and from your effects setup in one convenient module. The RockBoard® MODs provide a central access point from the instrument to the amplifier as well as a convenient and simple power supply to the board via an IEC and a 2.1 x 5.5 barrel-through power connector. The RockBoard® MOD 2 V2 was developed as a patchbay specifically for MIDI-based setups, amplifiers and devices as well as a USB connection between pedalboard and computer or sound card. With four TRS through connections, the MOD 2 V2 can be perfectly integrated into true stereo setups of keyboards or synthesisers or used as the central input and output of the board. Alternatively, effects pedals can be positioned in the front end and in the effects loop of the amplifier (4-cable method).

The RockBoard® MOD 5 Cab SIM + DI Patchbay offers selectable, IR-based stereo speaker simulation, an active DI box, and a simple solution to organise all connections to and from your effects setup. Whether you're using a RockBoard® or another brand of pedalboard, the MOD 5 opens up a whole new world of possibilities. With speaker cab simulation and DI, you can get started right away and have YOUR sound ready, no matter what backline is available at the venue. Want to use your personal favourite cabinet? No problem, load an Impulse Response of the sound into the MOD 5 and you have it with you wherever you go. The patchbay section is used to route connections from underneath your pedalboard to the front to give you a central access point to your setup and tidy up your cable clutter. For silent practice on the road, the MOD 5 also features a headphone amplifier with adjustable output volume.

The RockBoard ISO Power Block V6 is a multi power supply for effect devices and offers 5 galvanically isolated, highly filtered 9V DC power connections and a single 18V DC link connection to connect several ISO Power Blocks V6 in series and thus also operate larger effect setups. The advanced filter technology of the power slots effectively prevents high-frequency background noise. The separate short-circuit protection for the Power Slots protects the connected effect pedals from damage in the event of a short circuit. Separate LEDs indicate short circuits separately for each connection. If a short circuit occurs, only the affected power slot is switched off, so that the smooth operation of the effects rig is still guaranteed.

The revised RockBoard® MODs V2 are simple all-in-one patchbays for the RockBoard Pedalboard Series with a new, revised design and a compact housing. Suitable for all new RockBoards® (except the DUO series) with a MOD slot, they provide a convenient patchbay with various cable connections to cover a wide range of needs. With the RockBoard® MODs you can permanently wire your pedals under the board and organise all connections to and from your effects setup in one convenient module. The RockBoard® MODs provide a central access point from the instrument to the amplifier as well as a convenient and simple power supply to the board via an IEC and a 2.1 x 5.5 barrel-through power connector. The RockBoard® MOD 3 V2 is a patchbay for vocalists and acoustic musicians. You can send a stereo signal from your MOD via the two XLR outputs and a microphone can be connected to the XLR input. With three TRS through connections, the MOD 3 V2 can also be used as the central input and output of the board, for example to loop effects pedals into the FX loop of an amplifier.

The RockBoard MOD 4 - All-in-One Wireless System Receiver + Patchbay for Pedalboards offers an easy to realise wireless connection between your instrument and your pedalboard. It utilises digital wireless technology that guarantees impressive sound quality, easy setup and reliable use for active musicians. The wireless system operates in the 2.4 GHz ISM band and can therefore be used worldwide without restrictions. With a usable frequency range of 20 Hz - 20 kHz and only 5 ms latency, nothing is left to be desired. The patchbay section was developed to route connections and connectors of the pedalboard from the underside to the outside, to provide you with a central access point to your setup and to tidy up and organise your cable routes. The A, B, C and D TRS sockets are wired as direct, continuous connections from the front of the MOD 4 to the corresponding sockets on the rear. This allows you to set up your effects chain so that you only have to plug cables into the front of the board when preparing for the gig, instead of having to fiddle around under the board.

The RockBoard ISO Power Block V16 is a multi power supply for effect devices and offers 16 galvanically isolated, highly filtered power connections for the separate power supply of up to 15 effect pedals without background noise, as well as for charging USB devices. The advanced filter technology of the power slots effectively prevents high-frequency background noise. The separate short-circuit protection for the power slots protects the connected effect pedals from damage in the event of a short circuit. Separate LEDs indicate short circuits separately for each connection. If a short circuit occurs, only the affected power slot is switched off, so that the smooth operation of the effects rig is still guaranteed.