Cordial CPH 5 DMX 1 PWR 1
€79.00
card.manufacturer:
The CPH DMX 1 PWR 1 combination cable contains a mains cable and a DMX cable in a hybrid solution.According to DMX logic, the male plug is located on the receiver and the female plug on the transmitter (opposite to the approach used for XLR in the audio sector).Optimum power supply when using the hybrid on stage or in the studio is ensured by a 3x 1.5 mm2 mains cable and a balanced AES/EBU cable.The split of the cable is 30 cm.
Cordial CDX-1 10m
€46.00
card.manufacturer:
The CDX-1 offers an efficient solution for rental companies and event organisers in the field of stage lighting.This AES/EBU-certified DMX cable is equipped with black, 5-pin XLR female and XLR male metal connectors from Neutrik, the cable has 3-pin connectors.The high-quality CDMX-1 is used as the cable metreware, in which the pair shield is made of foil and the overall shielding consists of a braid of tinned copper wires. It fulfils the EIA 485 standard and DMX 512 specification and guarantees high tensile strength, especially for controlling intelligent spotlights, moving heads and dimmers. A transparent shrink sleeve has been attached to both ends so that the cable can be individually labelled during use.Please note the logic of the DMX standard, which is the reverse of the XLR logic in the audio sector. For DMX, a female connector is provided on the transmitter and a male connector on the receiver.
Cordial CPH 10 DMX 1 PWR 1
€105.00
card.manufacturer:
The CPH DMX 1 PWR 1 combination cable contains a mains cable and a DMX cable in a hybrid solution.According to DMX logic, the male plug is located on the receiver and the female plug on the transmitter (opposite to the approach used for XLR in the audio sector).Optimum power supply when using the hybrid on stage or in the studio is ensured by a 3x 1.5 mm2 mains cable and a balanced AES/EBU cable.The split of the cable is 30 cm.
Cordial CDX-2 20m
€90.60
card.manufacturer:
Lighting technicians and technical service providers looking for a high-quality DMX cable with 5-pin connectors and 5-pin cable assignment will find the CDX-2 to be a reliable partner for the long term.The inner workings of the CDMX-2 cable by the metre are protected from interference by a foil pair shield and a tinned copper wire braid.The CDX-2 fulfils the EIA 485 standard and DMX 512 specification. In order to withstand any load in the best possible way, Cordial paid attention to a particularly high tensile strength during development. This means that nothing can go wrong with the lighting control cable. A transparent shrink sleeve is attached to each end for individual cable labelling.Note the logic of the DMX standard: it is the reverse of the XLR logic in the audio sector. With DMX, there is a female plug on the transmitter and a male plug on the receiver.
Cordial CPH 1.5 DMX 1 PWR 1
€55.00
card.manufacturer:
The CPH DMX 1 PWR 1 combination cable contains a mains cable and a DMX cable in a hybrid solution.According to DMX logic, the male plug is located on the receiver and the female plug on the transmitter (opposite to the approach used for XLR in the audio sector).Optimum power supply when using the hybrid on stage or in the studio is ensured by a 3x 1.5 mm2 mains cable and a balanced AES/EBU cable.The split of the cable is 30 cm.
Cordial CDX-2 5m
€37.00
card.manufacturer:
The CDX-1 offers an efficient solution for rental companies and event organisers in the field of stage lighting.This AES/EBU-certified DMX cable is equipped with black, 5-pin XLR female and XLR male metal connectors from Neutrik, the cable has 3-pin connectors.The high-quality CDMX-1 is used as the cable metreware, in which the pair shield is made of foil and the overall shielding consists of a braid of tinned copper wires. It fulfils the EIA 485 standard and DMX 512 specification and guarantees high tensile strength, especially for controlling intelligent spotlights, moving heads and dimmers. A transparent shrink sleeve has been attached to both ends so that the cable can be individually labelled during use.Please note the logic of the DMX standard, which is the reverse of the XLR logic in the audio sector. For DMX, a female connector is provided on the transmitter and a male connector on the receiver.
Cordial CDX FN 3 Quad-DMX
€79.00
card.manufacturer:
The Ethercon QUAD DMX-AES/EBU adapter utilises one pair of wires of a common 4-pair CAT cable and thus enables the cost-efficient transport of four parallel DMX or AES/EBU signals.It is fitted with black female NEUTRIK® XLR metal connectors in 3-pin design. The individual cables are TIA 568 A colour-coded and terminate after a 70 cm split in a special metal cable socket with strain relief and kink protection based on the well-known NEUTRIK® NE8FF.We recommend network cables with at least one overall shield for the long distances in between. Distances of up to 150 metres are possible when using the high-quality CORDIAL CCAT 7A LONG RUN with a wire gauge of AWG 23.An ingenious solution for rental companies and event technology service providers in the "audio and video over IP" sector to extend the utilisation possibilities of high-quality network cable reels.
Cordial CDX-2 2m
€32.00
card.manufacturer:
The CDX-1 offers an efficient solution for rental companies and event organisers in the field of stage lighting.This AES/EBU-certified DMX cable is equipped with black, 5-pin XLR female and XLR male metal connectors from Neutrik, the cable has 3-pin connectors.The high-quality CDMX-1 is used as the cable metreware, in which the pair shield is made of foil and the overall shielding consists of a braid of tinned copper wires. It fulfils the EIA 485 standard and DMX 512 specification and guarantees high tensile strength, especially for controlling intelligent spotlights, moving heads and dimmers. A transparent shrink sleeve has been attached to both ends so that the cable can be individually labelled during use.Please note the logic of the DMX standard, which is the reverse of the XLR logic in the audio sector. For DMX, a female connector is provided on the transmitter and a male connector on the receiver.
Cordial CPH 10 DMX 1-5 PWR 1 K
€109.00
card.manufacturer:
Of course, time is a crucial factor during stage construction. Time must be saved, because it is limited and costs money. Cordial has developed the CPH DMX 1-5 PWR 1 to help equipment hire companies and event organisers with this issue.The hybrid cable combines the power supply with NEUTRIK® powerCON Power-In/Power-Out and a DMX cable with NEUTRIK® 5-pin XLR male/female connectors. For the use of LED walls, DMX-controlled spotlights and dimmer packs, for example, a precise 110 Ohm characteristic impedance cable was selected to generate a loop-through connection.In contrast to XLR in the audio sector, there is a female plug on the transmitter and a male plug on the receiver, in accordance with the logic of the DMX standard. The 5-pin f/m XLR plugs are 3-pin. For the power supply, the DMX/power combination cable is supplemented by a 3x 1.5 mm2 mains cable and a balanced AES/EBU cable.The split of the cable is 30 cm.
Klotz DMX5N2YS0300 DMX cable 3m
€44.00
card.manufacturer:
The DMX5N2YS transmits digital DMX lighting control signals. Low capacitance and attenuation, combined with very dense shielding with foil and braided shielding (coverage > 85 %), guarantee interference-free signal transmission, which is so important in the digital sector, even over long distances. Tightly stranded wire pairs increase immunity to external electromagnetic interference. The OT206 cable used has a characteristic impedance of 110 Ω, which is mandatory for digital signals. A robust PVC outer sheath with a diameter of just 6 mm ensures mechanical stability and also makes the cable very flexible. The DMX5N2YS is assembled with high-quality, 5-pin XLR connectors from Neutrik, fitted with blue coding rings. The outer sheath is provided with transparent shrink tubing on both sides for free labelling.
